快速查找
主营塑料
产品推荐
- ⊕PPS OL003A 含玻璃纤维,聚四氟乙
- ⊕PBT 420SE0 玻纤30%增强,阻燃级
- ⊕PBT 310SE0 非增强型,PBT阻燃树脂
- ⊕PP HJ730 高流动,高钢性,高耐热
- ⊕PP FB71U6 耐热级,抗UV,阻燃级
- ⊕PA6 73G30L NC010 玻璃纤维30%增
- ⊕PA66 70G43L NC010 玻璃纤维43%增
- ⊕PA66 70G33L NC010 玻璃纤维33%增
- ⊕PA66 70G30L NC010 玻璃纤维30%增
- ⊕PA66 80G33L NC010 玻纤33%增强,
- ⊕PA66 FR50 NC010A 玻纤25%增强,阻
- ⊕POM 900P NC010 低粘度,热稳定,低
- ⊕POM 500P NC010 中高粘,热稳定,低
- ⊕POM 100P NC010 高粘度,韧性好,热
- ⊕PBT SK605 NC010 玻璃纤维30%增强
- ⊕PA66 1300G 玻纤增强级
联系我们
- 产 品：PBT SHF4960 超高流量,玻纤30%填充,阻燃级,热稳定
- 产 地：沙伯基础创新
- 价 格：电话报价
- 库 存：20吨
- 交 货：江苏苏州
- 苏州希普能：185 5121 3137 谭经理
Valox* Resin
Valox* Resin All Series
The Valox* family of thermoplastic polyester resins are semi-crystalline materials based on polybutylene terephthalate (PBT) and/or polyethylene terephthalate (PET) polymers. Valox resins are highly tailorable, combining heat, chemical resistance, and outstanding electrical properties with exceptionally good processability and surface appearance.
Valox* Resin PBT SHF4960 数据表
Valox Super high flow grade, 30% glass filled Flame retardant, High CTI, heat stabilized with mold release.
Property
TYPICAL PROPERTIES (1)
| MECHANICAL | Value | Unit | Standard |
| Tensile Stress,yield,5mm/min | 110 | MPa | ISO 527 |
| Tensile Stress,break,5mm/min | 110 | MPa | ISO 527 |
| Tensile Strain,yield,5mm/min | 1.8 | % | ISO 527 |
| Tensile Strain,break,5mm/min | 1.8 | % | ISO 527 |
| Tensile Modulus,1mm/min | 10000 | MPa | ISO 527 |
| Flexural Stress,yield,2mm/min | 165 | MPa | ISO 178 |
| Flexural Modulus,2mm/min | 8500 | MPa | ISO 178 |
| IMPACT | Value | Unit | Standard |
| Izod Impact,unnotched 80*10*4 -30℃ | 36 | kJ/m² | ISO 180/1U |
| Izod Impact,notched 80*10*4 +23℃ | 7 | kJ/m² | ISO 180/1A |
| Izod Impact,notched 80*10*4 -30℃ | 7 | kJ/m² | ISO 180/1A |
| Charpy 23℃,V-notch Edgew 80*10*4 sp=62mm | 7 | kJ/m² | ISO 179/1eA |
| THERMAL | Value | Unit | Standard |
| CTE,-40℃ to 40℃,flow | 2.50E-05 | 1/℃ | ISO 11359-2 |
| CTE,-40℃ to 40℃,xflow | 1.20E-04 | 1/℃ | ISO 11359-2 |
| Vicat Softening Temp,Rate B/50 | 185 | ℃ | ISO 306 |
| Vicat Softening Temp,Rate B/120 | 195 | ℃ | ISO 306 |
| HDT/Af,1.8 MPa Flatw 80*10*4 sp=64mm | 195 | ℃ | ISO 75/Af |
| PHYSICAL | Value | Unit | Standard |
| Density | 1.64 | g/cm³ | ISO 1183 |
| Water Absorption,(23℃/sat) | 0.25 | % | ISO 62 |
| Moisture Absorption(23℃/50% RH) | 0.07 | % | ISO 62 |
| Melt Volume Rate,MVR at 250℃/2.16 kg | 6 | cm³/10 min | ISO 1133 |
| Melt Viscosity,250℃,1500 sec-1 | 92 | Pa-s | ISO 11443 |
| ELECTRICAL | Value | Unit | Standard |
| Volume Resistivity | >1.E+15 | Ohm-cm | IEC 60093 |
| Surface Resistivity,ROA | >1.E+12 | Ohm | IEC 60093 |
| Dielectric Strength,in oil,0.8mm | 35 | kV/mm | IEC 60243-1 |
| Dielectric Strength,in oil,1.6mm | 24.5 | kV/mm | IEC 60243-1 |
| Dielectric Strength,in oil,3.2mm | 17.8 | kV/mm | IEC 60243-1 |
| Comparative Tracking Index | 275 | V | IEC 60112 |
| FLAME CHARACTERISTICS | Value | Unit | Standard |
| UL Compliant, 94V-0 Flame Class Rating(3)(4) | 0.8 | mm | UL 94 by SABIC-IP |
| Oxygen Index(LOI) | 32 | % | ISO 4589 |
| Source GMD, last updated:2006/12/21 | |||
| Parameter Injection Molding | Value | Unit |
| Drying Temperature | 110-120 | ℃ |
| Drying Time | 2-4 | hrs |
| Maximum Moisture Content | 0.02 | % |
| Melt Temperature | 250-270 | ℃ |
| Nozzle Temperature | 240-260 | ℃ |
| Front-Zone 3 Temperature | 245-265 | ℃ |
| Middle-Zone 2 Temperature | 240-255 | ℃ |
| Rear-Zone 1 Temperature | 230-245 | ℃ |
| Hopper Temperature | 40-60 | ℃ |
| Mold Temperature | 40-100 | ℃ |
| Source GMD,last updated:2006/12/21 | ||
THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
Buy SABIC Innovative please contact xiang zhang Engineering plastics
1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards. PTFE 610A 聚四氟乙烯超细粉
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
关健字：【Valox* Resin PBT SHF4960】