旭化成 南亚 东丽 巴斯夫 罗地亚 普立万 长春

杜邦 泰科纳 三菱工程 GE料 朗盛 RTP 舒尔曼

改性尼龙 改性PBT 代理PTFE聚四氟乙烯粉

塑料种类

通用塑料 PVCGPPSHDPELDPEHIPSSAN

工程塑料 PVDFPSUPPSUPOPPFAPA4TPA9TPA6TPA610PA1010PA12PA11EPSEMAPPOCOCPA46PA6PA6/66PA612PEEKPPEPTFE

热塑弹性体CPETPVSISSBSSBRPBEPOETPX

联系我们

塑胶原料报价
PC FXD171R 透明/半透明PC,光扩散级
  • 产 品:PC FXD171R 透明/半透明PC,光扩散级
  • 产 地:沙伯基础创新
  • 价 格:电话报价
  • 库 存:20吨
  • 交 货:江苏苏州
  • 苏州希普能:185 5121 3137 谭经理

Lexan* Visualfx* Resin
Beauty Is More Than Skin Deep
Lexan Polycarbonate Visualfx Resins provide molded-in effects that can eliminate the need for modifications after molding. This can provide cleaner and more vibrant part aesthetics that will last as long as the part lasts. Visualfx Resins include Diamond, Luminescent, Diffusion, Lustre, and Edge Glow, as well as several metallic and natural material effects. Available in a variety of colors and base resins.

Lexan* Resin FXD171R 英文数据物性表
Transparent/transluscent PC for light diffusion special effects. MFR of 25.0.

Property
TYPICALPROPERTIES(1)

MECHANICAL Value Unit  Standard 
Tensile Stress,yld,Type I,50mm/min 630 kgf/cm² ASTM D 638
Tensile Stress,brk,Type I,50mm/min 650 kgf/cm² ASTM D 638
Tensile Strain,yld,Type I,50mm/min 6.2 % ASTM D 638
Tensile Strain,brk,Type I,50mm/min 125 % ASTM D 638
Tensile Modulus,50mm/min 23700 kgf/cm² ASTM D 638
Flexural Stress,yld,1.3mm/min,50mm span 940 kgf/cm² ASTM D 790
Flexural Modulus,1.3mm/min,50mm span 23900 kgf/cm² ASTM D 790
IMPACT Value Unit  Standard 
Izod Impact,notched,23℃ 79 cm-kgf/cm ASTM D 256
Instrumented Impact Total Energy,23℃ 714 cm-kgf ASTM D 3763
THERMAL Value Unit  Standard 
HDT,0.45 MPa,3.2mm,unannealed 137 ASTM D 648
HDT,1.82 MPa,3.2mm,unannealed 126 ASTM D 648
Relative Temp Index,Elec 130 UL 746B
Relative Temp Index,Mech w/impact 130 UL 746B
Relative Temp Index,Mech w/o impact 130 UL 746B
PHYSICAL Value Unit  Standard 
Specific Gravity 1.19 - ASTM D 792
Mold Shrinkage,flow,3.2mm (5) 0.5-0.7 % SABIC Method
Melt Flow Rate,300℃/1.2 kgf 25 g/10 min ASTM D 1238
ELECTRICAL Value Unit  Standard 
Hot Wire Ignition {PLC) 2 PLC Code UL 746A
High Voltage Arc Track Rate {PLC} 2 PLC Code UL 746A
High Ampere Arc Ign,surface {PLC} 1 PLC Code UL 746A
Comparative Tracking Index (UL) {PLC} 2 PLC Code UL 746A
FLAME CHARACTERISTICS Value Unit  Standard 
UL Recognized,94V-2 Flame Class Rating (3) 1.09 mm UL 94
Source GMD,last updated:2000/08/09
Parameter Injection Molding Value Unit 
Drying Temperature 120
Drying Time 3-4 hrs
Drying Time (Cumulative) 48 hrs
Maximum Moisture Content 0.02 %
Melt Temperature 270-295
Nozzle Temperature 265-290
Front-Zone 3 Temperature 270-295
Middle-Zone 2 Temperature 260-280
Rear-Zone 1 Temperature 250-270
Mold Temperature 70-95
Back Pressure 0.3-0.7 MPa
Screw Speed 40-70 rpm
Shot to Cylinder Size 40-60 %
Vent Depth 0.025-0.076 mm
Source GMD,last updated:2000/08/09

• NOTE: Back Pressure, Screw Speed, Shot to Cylinder Size and Vent Depth are only mentioned as general guidelines. These may not apply or need adjustment in specific situations such as low shot sizes, thin wall molding and gas-assist molding.

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
PLEASE CONTACT US FOR AVAILABILITY IN YOUR REGION.

1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
代理沙伯基础创新塑料(PC)聚碳酸酯材料

链接:ABS PA-746 高流动性