快速查找
主营塑料
产品推荐
- ⊕PPS OL003A 含玻璃纤维,聚四氟乙
- ⊕PBT 420SE0 玻纤30%增强,阻燃级
- ⊕PBT 310SE0 非增强型,PBT阻燃树脂
- ⊕PP HJ730 高流动,高钢性,高耐热
- ⊕PP FB71U6 耐热级,抗UV,阻燃级
- ⊕PA6 73G30L NC010 玻璃纤维30%增
- ⊕PA66 70G43L NC010 玻璃纤维43%增
- ⊕PA66 70G33L NC010 玻璃纤维33%增
- ⊕PA66 70G30L NC010 玻璃纤维30%增
- ⊕PA66 80G33L NC010 玻纤33%增强,
- ⊕PA66 FR50 NC010A 玻纤25%增强,阻
- ⊕POM 900P NC010 低粘度,热稳定,低
- ⊕POM 500P NC010 中高粘,热稳定,低
- ⊕POM 100P NC010 高粘度,韧性好,热
- ⊕PBT SK605 NC010 玻璃纤维30%增强
- ⊕PA66 1300G 玻纤增强级
联系我们
- 产 品：PC/ABS NX05467 无氯溴阻燃级合金
- 产 地：美国液氮
- 价 格：电话报价
- 库 存：20吨
- 交 货：江苏苏州
- 苏州希普能：185 5121 3137 谭经理
LNP* Colorcomp* Compound
LNP Colorcomp All Series
LNP* Colorcomp* resins contain colorants and special effects for a dazzling spectrum of colored materials. Among the offerings are opaque, translucent, and transparent resins, plus special effects, including edge glow, sparkle, glow, pearlescent, and thermochromic. LNP specialty compound offerings are available in a broad portfolio of standard and engineering materials.
LNP™Colorcomp™ Compound PC+ABS NX05467 数据
Also known as:LNP™Colorcomp™Compound Cycoloy C6200
Product reorder name:NX05467
LNP* Colorcomp* NX05467 is a compound based on Polycarbonate and ABS. Characteristics are: Non-Chlorinated, Non-Brominated Flame Retardant.
| MECHANICAL | Value | Unit | Standard |
| Tensile Stress,yield | 680 | kgf/cm² | ASTM D 638 |
| Tensile Strain,break | 50 | % | ASTM D 638 |
| Flexural Stress | 1050 | kgf/cm² | ASTM D 790 |
| Flexural Modulus | 27400 | kgf/cm² | ASTM D 790 |
| THERMAL | Value | Unit | Standard |
| HDT,1.82 MPa,3.2mm,unannealed | 87-91 | ℃ | ASTM D 648 |
| PHYSICAL | Value | Unit | Standard |
| Specific Gravity | 1.18 | - | ASTM D 792 |
| Mold Shrinkage,flow(5) | 0.4-0.6 | % | SABIC Method |
| Mold Shrinkage,xflow(5) | 0.4-0.6 | % | SABIC Method |
| ELECTRICAL | Value | Unit | Standard |
| Volume Resistivity | 1.00E+15 | Ohm-cm | ASTM D 257 |
| Surface Resistivity | 1.00E+15 | Ohm | ASTM D 257 |
| Dielectric Strength,in oil,0.8mm | 890 | kV/mm | IEC 60243-1 |
| Dielectric Strength,in oil,1.6mm | 640 | kV/mm | IEC 60243-1 |
| Dielectric Strength,in oil,3.2mm | 430 | kV/mm | IEC 60243-1 |
| Relative Permittivity,60 Hz | 2.8 | - | IEC 60250 |
| Relative Permittivity,1 MHz | 2.7 | - | IEC 60250 |
| Dissipation Factor,50/60 Hz | 0.004 | - | IEC 60250 |
| Dissipation Factor,1 MHz | 0.008 | - | IEC 60250 |
| FLAME CHARACTERISTICS | Value | Unit | Standard |
| UL Recognized,94HB Flame Class Rating(3) | 0.7 | mm | UL 94 |
| UL Recognized,94V-1 Flame Class Rating(3) | 1.2 | mm | UL 94 |
| UL Recognized,94V-0 Flame Class Rating(3) | 1.5 | mm | UL 94 |
| UL Recognized,94-5VA Rating(3) | 3.4 | mm | UL 94 |
| UL Recognized,94-5VB Rating(3) | 2.1 | mm | UL 94 |
| Source GMD,last updated:2010/08/31 | |||
| Parameter Injection Molding | Value | Unit |
| Drying Temperature | 80-90 | ℃ |
| Drying Time | 3-4 | hrs |
| Drying Time(Cumulative) | 8 | hrs |
| Maximum Moisture Content | 0.04 | % |
| Melt Temperature | 245-275 | ℃ |
| Nozzle Temperature | 245-275 | ℃ |
| Front-Zone 3 Temperature | 245-275 | ℃ |
| Middle-Zone 2 Temperature | 220-265 | ℃ |
| Rear-Zone 1 Temperature | 220-255 | ℃ |
| Mold Temperature | 60-80 | ℃ |
| Back Pressure | 0.3-0.7 | MPa |
| Screw Speed | 40-70 | rpm |
| Shot to Cylinder Size | 30-80 | % |
| Vent Depth | 0.038-0.076 | mm |
| Source GMD,last updated:2010/08/31 | ||
THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
Buy SABIC Innovative please contact xiang zhang Engineering plastics
1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.TPE PB-511 非加油胶
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
关健字：【LNP™Colorcomp™ Compound PC+ABS NX05467】