旭化成 南亚 东丽 巴斯夫 罗地亚 普立万 长春

杜邦 泰科纳 三菱工程 GE料 朗盛 RTP 舒尔曼

改性尼龙 改性PBT 代理PTFE聚四氟乙烯粉

塑料种类

通用塑料 PVCGPPSHDPELDPEHIPSSAN

工程塑料 PVDFPSUPPSUPOPPFAPA4TPA9TPA6TPA610PA1010PA12PA11EPSEMAPPOCOCPA46PA6PA6/66PA612PEEKPPEPTFE

热塑弹性体CPETPVSISSBSSBRPBEPOETPX

联系我们

塑胶原料报价
PA66 R2000 含专有的润滑剂复合尼龙66
  • 产 品:PA66 R2000 含专有的润滑剂复合尼龙66
  • 产 地:美国液氮
  • 价 格:电话报价
  • 库 存:20吨
  • 交 货:江苏苏州
  • 苏州希普能:185 5121 3137 谭经理

LNP LUBRILOY* POLYAMIDES COMPOUND
TOUGH & STRONG -- WITH UNIQUE LUBRICITY
Polyamide-based LNP Lubriloy compounds provide enhanced lubrication through a unique, patented lubrication technology.

LNP™ LUBRILOY™ Compound PA66 R2000 塑料物性表

Also known as:LNP™ Lubriloy™ Compound R
Product reorder name:R2000
LNP* Lubriloy* R2000 is a compound based on Nylon 66 resin containing Proprietary Lubricant. Added features of this material include: Internally Lubricated.

MECHANICAL Value Unit Standard
Tensile Stress,yield 580 kgf/cm² ASTM D 638
Tensile Stress,break 560 kgf/cm² ASTM D 638
Tensile Strain,yield 14 % ASTM D 638
Tensile Strain,break 27 % ASTM D 638
Tensile Modulus,50mm/min 24600 kgf/cm² ASTM D 638
Flexural Stress 830 kgf/cm² ASTM D 790
Flexural Modulus 23600 kgf/cm² ASTM D 790
Tensile Stress,break 53 MPa ISO 527
Tensile Strain,break 32.3 % ISO 527
Flexural Stress 65 MPa ISO 178
Flexural Modulus 2000 MPa ISO 178
IMPACT Value Unit Standard
Izod Impact,unnotched,23℃ 175 cm-kgf/cm ASTM D 4812
Izod Impact,notched,23℃ 6 cm-kgf/cm ASTM D 256
Izod Impact,unnotched 80*10*4 +23℃ 141 kJ/m² ISO 180/1U
Izod Impact,notched 80*10*4 +23℃ 6 kJ/m² ISO 180/1A
THERMAL Value Unit Standard
HDT,1.82 MPa,3.2mm,unannealed 77 ASTM D 648
CTE,-40℃ to 40℃,flow 7.74E-05 1/℃ ASTM E 831
CTE,-40℃ to 40℃,xflow 1.03E-04 1/℃ ASTM E 831
HDT/Af,1.8 MPa Flatw 80*10*4 sp=64mm 85 ISO 75/Af
PHYSICAL Value Unit Standard
Density 1.03 g/cm³ ASTM D 792
Moisture Absorption,50% RH,24 hrs 0.25 % ASTM D 570
Mold Shrinkage,flow,24 hrs(5) 1.8-2.2 % ASTM D 955
Mold Shrinkage,xflow,24 hrs(5) 2.1-3.1 % ASTM D 955
Wear Factor Washer 50 10^-10 in^5-min/ft-lb-hr ASTM D 3702 Modified
Dynamic COF 0.36 - ASTM D 3702 Modified
Static COF 0.27 - ASTM D 3702 Modified
Density 1.03 g/cm³ ISO 1183
Source GMD,last updated:2004/09/30
Parameter Injection Molding Value Unit
Drying Temperature 80
Drying Time 4 hrs
Maximum Moisture Content 0.15-0.25 %
Melt Temperature 270-280
Front-Zone 3 Temperature 295-305
Middle-Zone 2 Temperature 280-295
Rear-Zone 1 Temperature 265-275
Mold Temperature 80-95
Back Pressure 0.2-0.3 MPa
Screw Speed 30-60 rpm
Source GMD,last updated:2004/09/30

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
Buy SABIC Innovative please contact xiang zhang Engineering plastics

1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

关健字:【LNP™ LUBRILOY™ Compound PA66 R2000