快速查找
主营塑料
产品推荐
- ⊕PPS OL003A 含玻璃纤维,聚四氟乙
- ⊕PBT 420SE0 玻纤30%增强,阻燃级
- ⊕PBT 310SE0 非增强型,PBT阻燃树脂
- ⊕PP HJ730 高流动,高钢性,高耐热
- ⊕PP FB71U6 耐热级,抗UV,阻燃级
- ⊕PA6 73G30L NC010 玻璃纤维30%增
- ⊕PA66 70G43L NC010 玻璃纤维43%增
- ⊕PA66 70G33L NC010 玻璃纤维33%增
- ⊕PA66 70G30L NC010 玻璃纤维30%增
- ⊕PA66 80G33L NC010 玻纤33%增强,
- ⊕PA66 FR50 NC010A 玻纤25%增强,阻
- ⊕POM 900P NC010 低粘度,热稳定,低
- ⊕POM 500P NC010 中高粘,热稳定,低
- ⊕POM 100P NC010 高粘度,韧性好,热
- ⊕PBT SK605 NC010 玻璃纤维30%增强
- ⊕PA66 1300G 玻纤增强级
联系我们
Valox* Resin
Valox* Resin All Series
The Valox* family of thermoplastic polyester resins are semi-crystalline materials based on polybutylene terephthalate (PBT) and/or polyethylene terephthalate (PET) polymers. Valox resins are highly tailorable, combining heat, chemical resistance, and outstanding electrical properties with exceptionally good processability and surface appearance.
Valox* Resin PBT 325 数据表
General purpose, unreinforced, improved processing. Applications like sprinklers and nozzles, pumps, door handle, tank covers, pens, pencils etc.
Property
TYPICAL PROPERTIES (1)
MECHANICAL | Value | Unit | Standard |
Tensile Stress,yld,Type I,50mm/min | 520 | kgf/cm² | ASTM D 638 |
Tensile Strain,brk,Type I,50mm/min | 200 | % | ASTM D 638 |
Flexural Stress,yld,1.3mm/min,50mm span | 840 | kgf/cm² | ASTM D 790 |
Flexural Modulus,1.3mm/min,50mm span | 23900 | kgf/cm² | ASTM D 790 |
Hardness,Rockwell R | 117 | - | ASTM D 785 |
IMPACT | Value | Unit | Standard |
Izod Impact,unnotched,23℃ | 163 | cm-kgf/cm | ASTM D 4812 |
Izod Impact,notched,23℃ | 5 | cm-kgf/cm | ASTM D 256 |
Modified Gardner,23℃ | 414 | cm-kgf | ASTM D 3029 |
THERMAL | Value | Unit | Standard |
HDT,0.45 MPa,6.4mm,unannealed | 154 | ℃ | ASTM D 648 |
HDT,1.82 MPa,6.4mm,unannealed | 54 | ℃ | ASTM D 648 |
CTE,-40℃ to 40℃,flow | 8.10E-05 | 1/℃ | ASTM E 831 |
CTE,60℃ to 138℃,flow | 1.39E-04 | 1/℃ | ASTM E 831 |
Relative Temp Index,Elec | 120 | ℃ | UL 746B |
Relative Temp Index,Mech w/impact | 120 | ℃ | UL 746B |
Relative Temp Index,Mech w/o impact | 140 | ℃ | UL 746B |
PHYSICAL | Value | Unit | Standard |
Specific Gravity | 1.31 | - | ASTM D 792 |
Specific Volume | 0.76 | cm³/g | ASTM D 792 |
Water Absorption,24 hours | 0.08 | % | ASTM D 570 |
Water Absorption,equilibrium,23C | 0.34 | % | ASTM D 570 |
Mold Shrinkage,flow,0.75-2.3mm(5) | 0.9-1.6 | % | SABIC Method |
Mold Shrinkage,flow,2.3-4.6mm(5) | 1.5-2.3 | % | SABIC Method |
Mold Shrinkage,xflow,0.75-2.3mm(5) | 1-1.7 | % | SABIC Method |
Mold Shrinkage,xflow,2.3-4.6mm(5) | 1.6-2.4 | % | SABIC Method |
ELECTRICAL | Value | Unit | Standard |
Volume Resistivity | >4.E+16 | Ohm-cm | ASTM D 257 |
Dielectric Strength,in air,3.2mm | 15.7 | kV/mm | ASTM D 149 |
Dielectric Strength,in oil,1.6mm | 23.2 | kV/mm | ASTM D 149 |
Dielectric Strength,in oil,3.2mm | 15.7 | kV/mm | ASTM D 149 |
Relative Permittivity,100 Hz | 3.3 | - | ASTM D 150 |
Relative Permittivity,1 MHz | 3.1 | - | ASTM D 150 |
Dissipation Factor,100 Hz | 0.002 | - | ASTM D 150 |
Dissipation Factor,1 MHz | 0.02 | - | ASTM D 150 |
Arc Resistance,Tungsten{PLC} | 4 | PLC Code | ASTM D 495 |
Hot Wire Ignition{PLC) | 3 | PLC Code | UL 746A |
High Voltage Arc Track Rate{PLC} | 1 | PLC Code | UL 746A |
High Ampere Arc Ign,surface{PLC} | 0 | PLC Code | UL 746A |
Comparative Tracking Index(UL){PLC} | 0 | PLC Code | UL 746A |
FLAME CHARACTERISTICS | Value | Unit | Standard |
UL Recognized,94HB Flame Class Rating(3) | 0.83 | mm | UL 94 |
UV-light,water exposure/immersion | F1 | - | UL 746C |
Source GMD,last updated:2000/01/05 |
Parameter Injection Molding | Value | Unit |
Drying Temperature | 120 | ℃ |
Drying Time | 3-4 | hrs |
Drying Time(Cumulative) | 12 | hrs |
Maximum Moisture Content | 0.02 | % |
Melt Temperature | 245-260 | ℃ |
Nozzle Temperature | 240-255 | ℃ |
Front-Zone 3 Temperature | 245-260 | ℃ |
Middle-Zone 2 Temperature | 240-255 | ℃ |
Rear-Zone 1 Temperature | 230-250 | ℃ |
Mold Temperature | 50-75 | ℃ |
Back Pressure | 0.3-0.7 | MPa |
Screw Speed | 50-100 | rpm |
Shot to Cylinder Size | 40-80 | % |
Vent Depth | 0.013-0.025 | mm |
Source GMD,last updated:2000/01/05 |
THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
Buy SABIC Innovative please contact xiang zhang Engineering plastics
1、Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
2、Only typical data for selection purposes. Not to be used for part or tool design.
3、This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
4、Internal measurements according to UL standards.
5、Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
关健字:【Valox* Resin PBT 325】