Cycoloy* General Purpose FR Resin
General, Flame Retardant Resins
Polycarbonate/Acrylonitrile Butadiene Styrene (PC/ABS) alloy are designed for flame retardant applications, often used in electronic/electrical enclosures. Meets UL and other applicable standards.

Cycoloy* Resin CY6120 数据
Non-chlorinated and non-brominated flame retardant PC/ABS featuring good flow and impact properties. UL-94 V0 listed at 1.2mm intended for various thin wall applications.

Property
TYPICAL PROPERTIES (1)

MECHANICAL	Value	Unit	Standard
Tensile Stress,yld,Type I,50mm/min	630	kgf/cm²	ASTM D 638
Tensile Stress,brk,Type I,50mm/min	610	kgf/cm²	ASTM D 638
Tensile Strain,yld,Type I,50mm/min	4	%	ASTM D 638
Tensile Strain,brk,Type I,50mm/min	100	%	ASTM D 638
Tensile Modulus,50mm/min	30200	kgf/cm²	ASTM D 638
Flexural Stress,yld,1.3mm/min,50mm span	1040	kgf/cm²	ASTM D 790
Flexural Modulus,1.3mm/min,50mm span	28800	kgf/cm²	ASTM D 790
Tensile Stress,yield,50mm/min	58	MPa	ISO 527
Tensile Stress,break,50mm/min	49	MPa	ISO 527
Tensile Strain,yield,50mm/min	4	%	ISO 527
Tensile Strain,break,50mm/min	100	%	ISO 527
Tensile Modulus,1mm/min	2600	MPa	ISO 527
Flexural Stress,yield,2mm/min	93	MPa	ISO 178
Flexural Modulus,2mm/min	2500	MPa	ISO 178
IMPACT	Value	Unit	Standard
Izod Impact,notched,23℃	59	cm-kgf/cm	ASTM D 256
Instrumented Impact Total Energy,23℃	553	cm-kgf	ASTM D 3763
Izod Impact,notched 80*10*4 +23℃	40	kJ/m²	ISO 180/1A
THERMAL	Value	Unit	Standard
Vicat Softening Temp,Rate B/50	96	℃	ASTM D 1525
HDT,0.45 MPa,3.2mm,unannealed	93	℃	ASTM D 648
HDT,1.82 MPa,3.2mm,unannealed	85	℃	ASTM D 648
CTE,-40℃ to 40℃,flow	7.38E-05	1/℃	ASTM E 831
CTE,-40℃ to 40℃,xflow	8.46E-05	1/℃	ASTM E 831
CTE,23℃ to 80℃,flow	8.00E-05	1/℃	ISO 11359-2
CTE,23℃ to 80℃,xflow	8.00E-05	1/℃	ISO 11359-2
Vicat Softening Temp,Rate B/50	95	℃	ISO 306
Vicat Softening Temp,Rate B/120	98	℃	ISO 306
Relative Temp Index,Elec	60	℃	UL 746B
Relative Temp Index,Mech w/impact	60	℃	UL 746B
Relative Temp Index,Mech w/o impact	60	℃	UL 746B
PHYSICAL	Value	Unit	Standard
Specific Gravity	1.19	-	ASTM D 792
Mold Shrinkage,flow,3.2mm(5)	0.3-0.5	%	SABIC Method
Melt Flow Rate,260℃/2.16 kgf	18	g/10 min	ASTM D 1238
Melt Volume Rate,MVR at 260℃/2.16 kg	16	cm³/10 min	ISO 1133
ELECTRICAL	Value	Unit	Standard
Volume Resistivity	>1.E+15	Ohm-cm	IEC 60093
Surface Resistivity,ROA	>1.E+15	Ohm	IEC 60093
Dielectric Strength,in oil,3.2mm	17	kV/mm	IEC 60243-1
Relative Permittivity,1 MHz	2.6	-	IEC 60250
Dissipation Factor,50/60 Hz	0.004	-	IEC 60250
Dissipation Factor,1 MHz	0.008	-	IEC 60250
Relative Permittivity,50/60 Hz	2.7	-	IEC 60250
FLAME CHARACTERISTICS	Value	Unit	Standard
UL Recognized,94V-0 Flame Class Rating(3)	1.19	mm	UL 94
Source GMD,last updated:2002/04/11

Parameter Injection Molding	Value	Unit
Drying Temperature	80-90	℃
Drying Time	3-4	hrs
Drying Time(Cumulative)	8	hrs
Maximum Moisture Content	0.04	%
Melt Temperature	245-275	℃
Nozzle Temperature	245-275	℃
Front-Zone 3 Temperature	245-275	℃
Middle-Zone 2 Temperature	220-265	℃
Rear-Zone 1 Temperature	220-255	℃
Mold Temperature	60-80	℃
Back Pressure	0.3-0.7	MPa
Screw Speed	40-70	rpm
Shot to Cylinder Size	30-80	%
Vent Depth	0.038-0.076	mm
Source GMD,last updated:2002/04/11

THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES.
PLEASE CONTACT US FOR AVAILABILITY IN YOUR REGION.

(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hours storage at 23℃/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection molded samples. All samples tested under ISO test standards are prepared according to ISO 294.
(2) Only typical data for selection purposes. Not to be used for part or tool design.
(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
(4) Internal measurements according to UL standards.
(5) Measurements made from laboratory test coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.

PA66 90G33 玻纤增强级